[RGH]Collection of CPLD Diagrams

Tutorials and Guides about the Reset Glitch Hack in general
Post Reply
User avatar
tuxuser
Administrator
Administrator
Posts: 301
Joined: Sat Feb 19, 2011 4:53 pm
Location: Germany
Contact:

[RGH]Collection of CPLD Diagrams

Post by tuxuser » Fri Oct 21, 2011 10:15 am

Hey,
It would be cool if we could collect all diagrams for compatible CPLD boards which can be used for the Reset Glitch Hack.
Please post the diagram and write underneath whats the Target Revision (Slim/Fat).

GENERAL NOTES

SLIM
If the diagram mentions 220pF for the Capacitor value and your X360 Slim doesnt glitch good / at all - Try to use 270pF!

FAT
To *possibly* glitch a FAT Console better, stuff out the 1K Resistor, the 100nF Cap and the 3x 1N1418 Diodes and just connect the Voltage-Input Pin (the pin which is faced by the direction-stripe of the diodes) directly to 1,8V of an internal voltage regulator.
Thanks for the hint PDJ - Original Post

BOTH
Make the CPU_RST Wire exactly 32 cm to get the best results!
Last edited by tuxuser on Tue Nov 01, 2011 12:10 pm, edited 1 time in total.
I have no idea what I am doing but atleast I am trying

User avatar
tuxuser
Administrator
Administrator
Posts: 301
Joined: Sat Feb 19, 2011 4:53 pm
Location: Germany
Contact:

[RGH]Collection of CPLD Diagrams

Post by tuxuser » Fri Oct 21, 2011 10:46 am

Dangerous Prototypes / Seeedstudio Coolrunner II

FAT
[attach=1]

SLIM
[attach=2]

Verified: No

THAOYU XC2C64A Coolrunner-II Clone

FAT
[attach=3]

SLIM
[attach=4]

Verified: Yes

Xilinx Coolrunner II XC9500

FAT/SLIM
[attach=5]

Verified: No
Attachments
xc9500_cpld.jpg
thaoyou_SLIM.jpg
thaoyou_FAT.jpg
seeedstudiocoolrunner2SLIM.jpg
seeedstudiocoolrunner2FAT.jpg
Last edited by tuxuser on Sun Nov 13, 2011 9:14 pm, edited 1 time in total.
I have no idea what I am doing but atleast I am trying

xb0xguru

Re: [RGH]Collection of CPLD Diagrams

Post by xb0xguru » Tue Nov 08, 2011 1:55 am

I can confirm the THAOYU wiring posted works for both slim and fat consoles.

EdsonDario

Re: [RGH]Collection of CPLD Diagrams

Post by EdsonDario » Thu Nov 24, 2011 6:02 pm

I also confirm that THAOYU XC2C64A Coolrunner-II Clone works properly. I used 270pf.

c0sth4

Re: [RGH]Collection of CPLD Diagrams

Post by c0sth4 » Sun Dec 11, 2011 10:00 pm

Hello, can I ask you for some help?
I have
Xilinx Coolrunner II XC9500 but there is not installed  C1 C5 Leds, P2 etc... can you provide me some diagram  or write me, which parts are installed on that one which is on image? Or if its nescesary for using it in xbox? I can install it, but I cannot find complete datasheet or something what  could help me, Thank you very much...

smx

Re: [RGH]Collection of CPLD Diagrams

Post by smx » Mon May 14, 2012 9:55 am

Seeedstudio coolrunner works fine with my Falcon with the provided diagram. Sometimes the console doesn't boot and it freezes, but it's 1 fail on 10 boots. Normally it boots immediatly.

ddsdavey

Re: [RGH]Collection of CPLD Diagrams

Post by ddsdavey » Fri Jul 06, 2012 2:00 pm

Sorry if its an outdated thread but has anyone had any luck using these boards on RGH 2.0? I cannot for the life of me find any info,everyone has the Matrix etc.No info out there on the original boards like the ones featured on this page.

saso333
User
User
Posts: 2
Joined: Wed Aug 31, 2011 1:23 am

Re: [RGH]Collection of CPLD Diagrams

Post by saso333 » Fri Jul 06, 2012 10:34 pm

i can confirm that Xilinx Coolrunner II XC9500 works with RGH2 by adding 3.3k resistor & 680pf cap on CPU_RST line Jasper with slim setup

ddsdavey

Re: [RGH]Collection of CPLD Diagrams

Post by ddsdavey » Sat Jul 07, 2012 11:34 am

And thats the board im struggling with so great,thanks! do you use the same coolrunner points on phats that 12c_SDA & 12c_SDL use on slims ie pins 9 & 10? And that on Phat mobo 12C_SDA goes to J2B1-9 and 12C_SCL goes to J2B1-10?
One more thing (sorry!),i have to modify my board like this for slims...Image
I have to modify it differently for phats,but im thinking for RGH 2.0 the above is necessary even on Phats?
To be clear,i am wanting to do RGH 2.0 on a falcon.
And your advice,3.3k resistor to gnd on CPU_RST pin & 680pf cap in series on CPU_RST or again to gnd.
Sorry again for all these questions,just ignore me if you cannot be bothered lol but your the first person to give me a glimmer of hope!
Have you any sources for further info on cpld use with RGh 2.0 to save hassling you lol!
Thanks again.

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest